液壓登車橋應嚴格遵守超重，超負荷工作可能造就人和物的損傷；

The hydraulic boarding bridge shall strictly abide by the principle of overweight, and overload work may cause damage to people and objects;

在沒有護欄的升降平臺上工作，可能會使人員下墜，造就人員傷亡。

Working on the lifting platform without guardrail may cause personnel to fall and cause casualties.

為保證液壓登車橋處于良好工作狀態，使用前應提前做檢查：主要包括控制按鈕是否靈驗；電源線及插座是否完好；輸油管是否完好；護欄的穩固性；各交接點螺栓的緊固性；外觀質量的完好。但當電源接通，指示燈亮后，按上升按鈕，電機轉動而升降臺不上升，這可能是三相電源接反后電機倒轉，只需電源糾正即可，所以不是大問題。

In order to ensure that the hydraulic boarding axle is in good working condition, check in advance before use: mainly including whether the control button is effective; Whether the power cord and socket are intact; Whether the oil pipeline is intact; Stability of guardrail; Tightness of bolts at each junction point; The appearance quality is intact. However, when the power supply is turned on and the indicator light is on, press the rise button, the motor rotates and the lifting table does not rise. This may be that the motor reverses after the three-phase power supply is connected reversely. It only needs to be corrected by the power supply, so it is not a big problem.

液壓登車橋工作時須撐開支腿，調整支腿螺栓，使升降平臺平穩受力于支腿并保持水平；在升降過程中和升起狀態下，不得移動升降平臺，嚴禁在升降平臺上搖晃。

When the hydraulic support leg is lifted and lowered on the platform, the hydraulic support leg must be adjusted and kept horizontal; During the lifting process and in the lifting state, the lifting platform shall not be moved and shaking on the lifting platform is strictly prohibited.

液壓登車橋工作時有異常聲響，應立即停機檢查，以免造成升降臺嚴重破壞；使用前須檢查電氣設備是否正常；凡是軸銷油孔，每次使用前須加潤滑油。使用前須先作空載升降，檢查液壓系統是否正常；工作臺載重不得大于額定值，更不能做激烈的人為搖晃；油箱內的液壓油每工作500小時須更換一次。

If there is abnormal sound when the hydraulic boarding bridge works, stop the machine immediately for inspection to avoid serious damage to the lifting platform; Check whether the electrical equipment is normal before use; Lubricating oil must be added to all axle pin oil holes before each use. No load lifting and lowering must be carried out before use to check whether the hydraulic system is normal; The load of the workbench shall not be greater than the rated value, let alone violent artificial shaking; The hydraulic oil in the oil tank must be replaced every 500 hours.

登車橋工作結束后，應將各部擦洗清潔，不作業時應將工作臺下降低位置。

After boarding the axle, all parts shall be scrubbed and cleaned. When not working, the workbench shall be lowered to the low position.

液壓登車橋每月保養：滾輪、中間軸及軸承，油缸銷軸及軸承，臂架鉸軸及軸承等有無磨損；液壓油的油質和油位；液壓登車橋全程升起，在這位置時，液壓面應高出箱底40-50毫米。液壓油是變暗、發粘或有砂礫等異物，如有發現應及時更換；各部位均加注一些潤滑油，延長軸承使用壽命。液壓登車橋用途廣泛，做好以上幾點不但可以保障您的人身還可以延長設備的使用壽命，讓登車橋更好的為您服務。

Monthly maintenance of hydraulic boarding bridge: whether the roller, intermediate shaft and bearing, oil cylinder pin shaft and bearing, boom hinge shaft and bearing are worn; Oil quality and oil level of hydraulic oil; The hydraulic boarding axle is raised in the whole process. In this position, the hydraulic surface should be 40-50mm higher than the bottom of the box. The hydraulic oil is dark, sticky or has foreign matters such as gravel. If it is found, it should be replaced in time; All parts are filled with some lubricating oil to prolong the service life of the bearing. The hydraulic boarding bridge has a wide range of uses. Doing well in the above points can not only ensure your personal safety, but also prolong the service life of the equipment and make the boarding bridge serve you better.

以上就是為大家介紹的有關移動登車橋的詳細介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務

The above is a detailed introduction to the mobile boarding axle. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service